From East to West

“Working with Jim on this project, he knew what he wanted and gave us the freedom to run with his ideas—the project took two years and required only three meetings between us to pull it together,” Simard surmised. The road to Pomona, California, from Leominster, Massachusetts, began after the initial acquisition of the gennie ’32 Ford, which again according to Simard, “…still had the original upholstery”. However, that Mohair wouldn’t last long, nor would much of the original interior other than maybe the dash panel shell. But the insides would come at the tail end of the two-year build.

First came the chassis. As earlier indicated, the stock ’32 Ford frame was part of the FoMoCo requisites. However, much like the interior, not every aspect made the cut, so to speak. In short, the framerails were bobbed front and rear as well as double-walled; custom crossmembers were fashioned and installed along with a custom tube X-member; and the rear was C-notched. The most notable part, however, has to be the completely custom-made torsion bar suspension—both fore and aft—featuring Shroeder torsion bars with a one-off torsion link system by East Coast Customs (ECC). The front is based around a ’37 Ford tube axle with hidden-mount ’35 Ford hydraulic shocks and handmade hairpin radius rods; on the opposing end is the Halibrand-equipped banjo with 9-inch Ford axles and long, Indy-style ladder bars. (After getting hand-finished, all suspension components were nickel-plated by Jon Wright.) Each of the four corners has been fitted with the Real Rodders Wheels “mags” (16x5/18x7) shod in Dunlop racing rubber with specially machined Wilwood disc brakes.

In lieu of going with an early type engine, Jim and Simard settled upon a 4.6L DOHC Ford modular motor—but not your ordinary dual-overhead, as the photos clearly show. Simard sourced a vintage Hilborn stack injector setup (circa 1955) and retrofit it using a FAST electronic fuel-injection system to work with the engine’s crank-triggered ignition. What appears to be a traditional distributor is actually an electronic water pump, while a Powermaster PowerGen alternator acts as an early looking generator. Simard whittled out a pair of valve covers reminiscent of an early Indy racer, bent up a stainless exhaust, incorporating Stainless Specialties mufflers, and to keep the modern essences to a minimum, facilitated a mechanical fan and tach drive. Behind the 4.6 mounts a Tremec five-speed with ECC-made mechanical clutch linkage setup.

As for the body, while it’s unquestionably a ’32 Ford, its genuine Henry tin has gone through some extensive re-massaging. Most notably is the absence of driver and passenger entry devices (though the functioning rumble lid handle is retained) and, of course, the custom hood sides with hand-hammered blisters. Forward of the stock hood top, the original grille shell has been filled, now void of its radiator cap and bullnose but with the addition of a “frenched” ’33 Ford Blue Oval cloisonné.

Simard chopped the windshield 3 inches, and in doing so integrated a ’36 roadster top rail. After painstaking bodywork by ECC, Kevin Olson sprayed the roadster using custom-mixed DuPont maroon. In the absence of the stock exposed gas tank, Simard crafted an aluminum roll pan, which, as you can see, wasn’t affected by Olson’s spray gun. He also added a custom rear nerf bar and abbreviated front nerf/headlight bar (mounting a pair of Guides), both of which were nickel-plated. The taillights you see are not of Lincoln origin, rather, ’39 Ford units that have added bezel features.

Finally, before the V-8 Flyer headed West, its racy yet coachbuilt-styled interior was tended to. Prior to its visit to New Hampshire, where Steve Pierce would fashion together the leather trimming, Simard built the engine-turned stainless dash insert, ultimately fitting it with an array of vintage Stewart-Warner gauges (restored by Instrument Specialties, with the tach and speedo supplied by Pat Swanson) as well as incorporating a sleek underdash panel housing the fuel cutoff, kill switch, turn signals, and indicator lights. That Delage-looking steering wheel is actually the handiwork of Dick Courville, machined out of aluminum and wrapped in black leather by Pierce, who also fabbed up the bucket seats prior to laying out the saddle tan leather and unique rubber matted flooring in the cockpit.

Now that Jim Farley’s ’32 Ford roadster, the “V-8 Flyer” as he’s named it, is finished and has done the whole show thing, it’s time for him to enjoy the “dependable hot rod” aspect he and Simard agreed on from the get go. And believe us, he will.

Rod & Custom Feature Car

Jim Farley

Detroit, Michigan

1932 Ford Roadster